|
cableTVamps.com provides the following
selection of power inserters, couplers,
terminators and power supplies, and various other
components to complement your existing configuration or new cable amplifier
purchase:
|
|
F-Terminator
 |
|
View Full Product Details
$1.50 USD
|
|
F-Terminator: Terminators
are used on open amplifier ports, or any outlet in your home where there is no
TV connected. Terminators help eliminate ghosts and noise in the cable picture
due to open connections.
|
|
F-Coupler
 |
|
View Full Product Details
$1.50 USD
|
|
F-Coupler:
F-Couplers are used to connect two cables together. Both sides are threaded
female F connections.
Use this F type coupler, also
called an F81 coupler, to connect two standard coax cables with F type male ends
together. |
|
EDA-PS (15v
Power Supply)
 |
|
View Full Product Details
$12.00 USD
|
|
The EDA-PS power
supply is a direct replacement for the power supply included with the
Electroline Series of Drop Amplifiers. It supplies 200ma at 15VDC. It is
over-current protected so that the drop amplifier is protected from a voltage
surge.
This power supply uses the screw-on type F connector. This power supply will
work with Electroline, Scientific Atlanta, Motorola, Viewsonics, and most any
cable amplifier that requires a 12-15VDC 200ma power supply. |
|
EDA-PS (18v
Power Supply)
For Electroline EDA-FT08100
 |
|
View Full Product Details
$16.00 USD
|
|
EDA-PS (18v Power Supply):
Electroline 18v replacement power supply. Supplies 18VDC. 600ma, with
over-current protection. Will work with the following Electroline amplifiers:
EDA-FT08100
ONLY. |
|
EDA-PS (13v
Power Supply)
For Electroline EDA-FT08300
|
|
View Full Product Details
$18.00 USD
|
|
EDA-PS (13v Power Supply):
Electroline 13v replacement power supply. Supplies 13VDC 350ma, with
over-current protection. Will work with the following Electroline amplifiers:
EDA-FT08300
ONLY. |
|
EDA-ICF
(Power Inserter)
|
|
View Full Product Details
$7.00 USD
|
|
EDA-ICF (Power Inserter):
Power Inserters are used when there is no power outlet close to the amplifier
mounting location. Power inserters allow the power to be supplied to the cable amplifier
by using one of your existing TV or cable box connections. Instructions for use
come with every cable amplifier, or can be emailed to you on request.
|
|
3dB Signal
Attenuator
|
|
View Full Product Details
$3.00 USD
|
|
3dB Signal Attenuator:
3dB attenuator decreases signal strength by about half. These are used to cut
the signal strength if the signal is too strong coming out of an amplifier or
going into an amplifier. Please email us for instructions if you need to use
this product.
|
|
6dB Signal
Attenuator
|
|
View Full Product Details
$3.50 USD
|
|
6dB Signal Attenuator:
6dB attenuator decreases signal strength by about 75%. These are used to cut
the signal strength if the signal is too strong coming out of an amplifier or
going into an amplifier. Please email us for instructions if you need to use
this product.
|
|
8dB Signal
Attenuator
|
|
View Full Product Details
$4.00 USD
|
|
8dB Signal Attenuator:
8dB attenuator decreases signal strength by about
84%. These are used to cut
the signal strength if the signal is too strong coming out of an amplifier or
going into an amplifier. Please email us for instructions if you need to use
this product.
|
|
10dB Signal
Attenuator
|
|
View Full Product Details
$4.50 USD
|
|
10dB Signal Attenuator:
10dB attenuator decreases signal strength by about
90%. These are used to cut
the signal strength if the signal is too strong coming out of an amplifier or
going into an amplifier. Please email us for instructions if you need to use
this product.
|
|
12dB Signal
Attenuator
|
|
View Full Product Details
$5.00 USD
|
|
12dB Signal Attenuator:
12dB attenuator decreases signal strength by about
93%. These are used to cut
the signal strength if the signal is too strong coming out of an amplifier or
going into an amplifier. Please email us for instructions if you need to use
this product.
|
|
T-Seal
|
|
View Full Product Details
$1.00 USD
|
|
T-Seal: Molded rubber
T-Seal helps protect cable connections from moisture and damaging mud, dust or
dirt. Accommodates standard CATV "F" connectors. T-Seals are used to seal the
gap between male and female "F" type connectors in outdoor applications. Easy to
Install - Slips on in Seconds |
|
Weather Boots
 |
|
View Full Product Details
$1.00 USD
|
|
Weather Boots: Weather
resistant coax boots fit RG6 and RG59 coax cable. Weather boots are typically
used outdoors to protect the type F connector.
UV-protected. |
|
Coaxial Lightning Surge Protector
(TII 210)
|
|
View Full Product Details
$15.00 USD
|
|
TII 210 Coaxial Lightning
Surge Protector: Prevent problems with a professional lightning surge
protector. Protects Virtually All Home Electronics From Even The Smallest
Surges. This coax lightning surge protector Incorporates The Fire-Protection
Technology To Be UL certified and provides years of protection against multiple
surges. It is sealed to prevent moisture. It is Ideally suited to shield costly
digital set-top boxes, expensive stereos and home equipment systems, sensitive
internet cable modems, personal computers, digital satellite TV systems, big
screen TVs and high-end HDTV sets from potentially damaging surges. |
|
Coaxial Lightning Surge Protector
(TII 212)
 |
|
View Full Product Details
$18.00 USD
|
|
TII 212 Coaxial Lightning
Surge Protector: Prevent problems with a professional lightning surge
protector. Protects Virtually All Home Electronics From Even The Smallest
Surges. This coax lightning surge protector Incorporates The Fire-Protection
Technology To Be UL certified and provides years of protection against multiple
surges. It is sealed to prevent moisture. It is Ideally suited to shield costly
digital set-top boxes, expensive stereos and home equipment systems, sensitive
internet cable modems, personal computers, digital satellite TV systems, big
screen TVs and high-end HDTV sets from potentially damaging surges. The 212
model incorporates the grounding block directly into the unit. |
Single Coax Line Grounding Block
 |
|
View Full Product Details
$6.00 USD
|
|
Single Coax Line Grounding Block:
These components are a must in every cable system. Expensive devices attached to
CATV or distributed coaxial systems are susceptible to damage from static and
surge damage. Proper grounding and suppression are key in minimizing risk. Used
for grounding long cable runs to eliminate static. Connects coax cable while
preventing electric surges. Use indoors or outdoors. Easy installation. Use one
of these to ground your coax lines and prevent surges from wiping out your
expensive equipment. Add on one of our surge protectors for an additional layer
of protection. |
|
Thomas & Betts
Snap-N-Seal Dual Shield RG-6 Connectors
 |
|
View Full Product Details
Bag of 10
$7.50 USD
|
|
Thomas & Betts Snap-N-Seal Dual Shield RG-6
Connectors:
Snap-N-Seal
connectors are environmentally sealed for protection against harsh environments.
Their 360° compression process offers the signal leakage protection required for
today's advanced cable systems.
These connectors feature a connector to cable retention of 40 lbs minimum;
Superb return loss performance of -30dB to 1GHz; True 360 degree compression
onto cable ensures superior RF shielding performance, -95dB effective shielding
(typical on 60% bonded foil cable) and provides superior RF integrity;
Manufactured of high quality 360 brass, cadmium plated with yellow chromate
coating for maximum corrosion resistance; and UV resistant plastic and O-rings
provide a reliable environmentally sealed connector.
These connectors are for
use with Dual Shield cable only! |
|
Thomas & Betts
Snap-N-Seal Quad Shield RG-6 Connectors
 |
|
View Full Product Details
Bag of 10
$7.50 USD
|
|
Thomas & Betts Snap-N-Seal Quad Shield RG-6
Connectors:
Snap-N-Seal
connectors are environmentally sealed for protection against harsh environments.
Their 360° compression process offers the signal leakage protection required for
today's advanced cable systems.
These connectors feature a connector to cable retention of 40 lbs minimum;
Superb return loss performance of -30dB to 1GHz; True 360 degree compression
onto cable ensures superior RF shielding performance, -95dB effective shielding
(typical on 60% bonded foil cable) and provides superior RF integrity;
Manufactured of high quality 360 brass, cadmium plated with yellow chromate
coating for maximum corrosion resistance; and UV resistant plastic and O-rings
provide a reliable environmentally sealed connector.
These connectors are for
use with Quad Shield cable only! |
|
Ground Loop Isolator (VSIS-EU)
|
|
View Full Product Details
$29.00 USD
|
|
Ground Loop Isolator (VSIS-EU): A Ground Isolator is used to eliminate the hum and
horizontal bars caused by ground loops. When two or more devices are connected
to a common ground through different paths, ground path noise or a ground loop
can occur. This is actually quite common in home cable systems, even those that
are well designed. The result of a ground loop is audio hum and/or horizontal
bars in the TV picture.
If “beefing up" conventional ground connections
and establishing solid ground points in your cable system does not resolve these
problems, then a Ground Isolator is the most reliable way to fix it. The
Ground Loop Isolator creates an electrical open on the outside shield, designed to work from 0-100Hz (DC current and AC current
frequencies). The isolator allows cable signals above 100Hz to pass regardless
of whether a ground differential exists between the two connection points.
It is virtually invisible to cable boxes and cable modems.
|
|
|
|
|
